We recommend that you have a dedicated server for Logsign Unified SecOps Platform. The disk that you allocated for Logsign Unified SecOps Platform is formatted during Logsign Unified SecOps Platform installation process. The ISO file of Logsign Unified SecOps Platform software is integrated with Ubuntu 64 Bit, and Logsign Unified SecOps Platform is installed on the Ubuntu operating system. For this reason, we recommend not to install Logsign Unified SecOps Platform on an existing server as you may lose all your data.
Important Note: The server specs must be dedicated on Logsign. ( Not Dynamic/Shared)
The following ISO file is required to install Logsign Unified SecOps Platform :
Please follow these steps to complete the installation.
For installation on a physical server:
- Burn the DVD or USB flash drive with the Logsign Unified SecOps Platform .iso file.
- You can boot the server via DVD disc or USB flash drive.
- The server will boot with the DVD or USB as a primary boot device.
For installation on a virtual server:
- Create a new virtual server with the specs listed in the System Requirements article.
- You must give dedicated sources for vm (cpu,ram,disk)
- You must select thick provisioning on disk settings.
- You need to upload the iso file to datastore of your virtual server.
- You need to mount the ISO file on virtual server and select the checkbox of “Connected”.
6. Installation process begins as shown below:
7. Assign the IP address of Logsign Unified SecOps Platform in Configure the Network section.
8. The system reboot is required after the installation is complete.
9. The display shows the name of the host operating system and the IP address of your machine.
Open the web browser and go to https://LOGSIGN_IP_ADDRESS, using the IP address you assigned during installation. You will be directed to the setup wizard, which has four tabs: License, Password, Email and Finish.
10. On the License tab, choose "I have a license key" if you have a license key. For the trial version of Logsign Unified SecOps Platform, choose "30 days trial".
Fill in the information needed:
Host ID: Unique identification number of Logsign Unified SecOps Platform. It is filled in automatically and cannot be edited.
Serial: The serial key which is given to you when you purchased Logsign Unified SecOps Platform. This field does not appear if you choose "30 days trial".
Then, fill in the Name, Last Name, Company, E-mail and Phone fields. All of them are required. Name, Last Name and Company accept letters, numbers and spaces only.
Click Activate to activate the product.
Once the license is activated, the wizard moves on to the Password tab and you can not return to the License tab.
11. On the Password tab, set the password of the admin user for the web interface.
Password: Enter your web interface password. It must be at least 8 characters long and contain at least one number, one uppercase letter and one lowercase letter.
Confirm Password: Enter the same password again to confirm it.
Click Next to move to the next step.
We recommend you to choose a strong password which consists of a combination of uppercase and lowercase letters, numbers and special symbols, such as punctuation. You should avoid using common, easily hacked characters and reusing the same password across multiple accounts.
12. On the Email tab, enter the SMTP settings that Logsign will use to send notifications:
Use SMTP Authentication: Mark this box if your SMTP server requires authentication. The Username and Password fields appear only when this box is marked.
Username: Enter your username.
Password: Enter your password.
SMTP Port: Enter the port of the SMTP server. It may vary depending on the email provider.
Use TLS: Mark this box if your email provider uses the TLS service.
SMTP Server: Enter the server name of the SMTP e-mail provider.
From E-mail: Enter the e-mail address which will send the notifications.
Destination E-mail: Enter the e-mail address which will receive the notifications.
13. Click Next to save the settings and move to the next step. If you prefer to configure them at another time, you can click Skip.
In Finish section, the configuration of your setup wizard will be completed.
Click Launch Logsign to be directed to the login page.